Self-Limiting Phase Transition Enabling Reversible Overstoichiometric Li Storage in Ni-Rich Cathodes.

Ni-rich cathodes are some of the most promising candidates for advanced lithium-ion batteries, but their available capacities have been stagnant due to the intrinsic Li+ storage sites. Extending the voltage window down can induce the phase transition from O3 to 1T of LiNiO2-derived cathodes to accommodate excess Li+ and dramatically increase the capacity. By setting the discharge cutoff voltage of LiNi0.6Co0.2Mn0.2O2 to 1.4 V, we can reach an extremely high capacity of 393 mAh g-1 and an energy density of 1070 Wh kg-1 here. However, the phase transition causes fast capacity decay and related structural evolution is rarely understood, hindering the utilization of this feature. We find that the overlithiated phase transition is self-limiting, which will transform into solid-solution reaction with cycling and make the cathode degradation slow down. This is attributed to the migration of abundant transition metal ions into lithium layers induced by the overlithiation, allowing the intercalation of overstoichiometric Li+ into the crystal without the O3 framework change. Based on this, the wide-potential cycling stability is further improved via a facile charge-discharge protocol. This work provides deep insight into the overstoichiometric Li+ storage behaviors in conventional layered cathodes and opens a new avenue toward high-energy batteries.

Chemical-Mechanical Robustness of Single-Crystalline Ni-Rich Cathode Enabled by Surface Atomic Arrangement Control.

Layered transition metal oxide cathodes have been one of the dominant cathodes for lithium-ion batteries with efficient Li+ intercalation chemistry. However, limited by the weak layered interaction and unstable surface, mechanical and chemical failure plagues their electrochemical performance, especially for Ni-rich cathodes. Here, adopting a simultaneous elemental-structural atomic arrangement control based on the intrinsic Ni-Co-Mn system, the surface role is intensively investigated. Within the invariant oxygen sublattice of the crystal, a robust surface with the synergistic concentration gradient and layered-spinel intertwined structure is constructed on the model single-crystalline Ni-rich cathode. With mechanical strain dissipation and chemical erosion suppression, the cathode exhibits an impressive capacity retention of 82 % even at the harsh 60 °C after 150 cycles at 1 C. This work highlights the coupling effect of structure and composition on the chemical-mechanical properties, and the concept will spur more researches on the cathodes that share the same sublattice.

Size controllable single-crystalline Ni-rich cathodes for high-energy lithium-ion batteries.

A single-crystalline Ni-rich (SCNR) cathode with a large particle size can achieve higher energy density, and is safer, than polycrystalline counterparts. However, synthesizing large SCNR cathodes (>5 µm) without compromising electrochemical performance is very challenging due to the incompatibility between Ni-rich cathodes and high temperature calcination. Herein, we introduce Vegard's Slope as a guide for rationally selecting sintering aids, and we successfully synthesize size-controlled SCNR cathodes, the largest of which can be up to 10 µm. Comprehensive theoretical calculation and experimental characterization show that sintering aids continuously migrate to the particle surface, suppress sublattice oxygen release and reduce the surface energy of the typically exposed facets, which promotes grain boundary migration and elevates calcination critical temperature. The dense SCNR cathodes, fabricated by packing of different-sized SCNR cathode particles, achieve a highest electrode press density of 3.9 g cm-3 and a highest volumetric energy density of 3000 Wh L-1. The pouch cell demonstrates a high energy density of 303 Wh kg-1, 730 Wh L-1 and 76% capacity retention after 1200 cycles. SCNR cathodes with an optimized particle size distribution can meet the requirements for both electric vehicles and portable devices. Furthermore, the principle for controlling the growth of SCNR particles can be widely applied when synthesizing other materials for Li-ion, Na-ion and K-ion batteries.

Mitigating Swelling of the Solid Electrolyte Interphase using an Inorganic Anion Switch for Low-temperature Lithium-ion Batteries.

In overcoming the Li+ desolvation barrier for low-temperature battery operation, a weakly-solvated electrolyte based on carboxylate solvent has shown promises. In case of an organic-anion-enriched primary solvation sheath (PSS), we found that the electrolyte tends to form a highly swollen, unstable solid electrolyte interphase (SEI) that shows a high permeability to the electrolyte components, accounting for quickly declined electrochemical performance of graphite-based anode. Here we proposed a facile strategy to tune the swelling property of SEI by introducing an inorganic anion switch into the PSS, via LiDFP co-solute method. By forming a low-swelling, Li3 PO4 -rich SEI, the electrolyte-consuming parasitic reactions and solvent co-intercalation at graphite-electrolyte interface are suppressed, which contributes to efficient Li+ transport, reversible Li+ (de)intercalation and stable structural evolution of graphite anode in high-energy Li-ion batteries at a low temperature of -20 °C.

Building a Self-Adaptive Protective Layer on Ni-Rich Layered Cathodes to Enhance the Cycle Stability of Lithium-Ion Batteries.

Layered Ni-rich lithium transition metal oxides are promising battery cathodes due to their high specific capacity, but their poor cycling stability due to intergranular cracks in secondary particles restricts their practical applications. Surface engineering is an effective strategy for improving a cathode's cycling stability, but most reported surface coatings cannot adapt to the dynamic volume changes of cathodes. Herein, a self-adaptive polymer (polyrotaxane-co-poly(acrylic acid)) interfacial layer is built on LiNi0.6 Co0.2 Mn0.2 O2 . The polymer layer with a slide-ring structure exhibits high toughness and can withstand the stress caused by particle volume changes, which can prevent the cracking of particles. In addition, the slide-ring polymer acts as a physicochemical barrier that suppresses surface side reactions and alleviates the dissolution of transition metallic ions, which ensures stable cycling performance. Thus, the as-prepared cathode shows significantly improved long-term cycling stability in situations in which cracks may easily occur, especially under high-rate, high-voltage, and high-temperature conditions.

Kinetic Origin of Planar Gliding in Single-Crystalline Ni-Rich Cathodes.

Single-crystalline Ni-rich cathodes with high capacity have drawn much attention for mitigating cycling and safety crisis of their polycrystalline analogues. However, planar gliding and intragranular cracking tend to occur in single crystals with cycling, which undermine cathode integrity and therefore cause capacity degradation. Herein, we intensively investigate the origin and evolution of the gliding phenomenon in single-crystalline Ni-rich cathodes. Discrete or continuous gliding forms are revealed with new surface exposure including the gliding plane (003) and reconstructed (-108) under surface energy drive. It is also demonstrated that the gliding process is the in-plane migration of transition metal ions, and reducing oxygen vacancies will increase the migration energy barrier by which gliding and microcracking can be restrained. The designed cathode with less oxygen deficiency exhibits outstanding cycling performance with an 80.8% capacity retention after 1000 cycles in pouch cells. Our findings provide an insight into the relationship between defect control and chemomechanical properties of single-crystalline Ni-rich cathodes.

An Air-Stable High-Nickel Cathode with Reinforced Electrochemical Performance Enabled by Convertible Amorphous Li2 CO3 Modification.

High-nickel (Ni ≥ 90%) cathodes with high specific capacity hold great potential for next-generation lithium-ion batteries (LIBs). However, their practical application is restricted by the high interfacial reactivity under continuous air erosion and electrolyte assault. Herein, a stable high-nickel cathode is rationally designed via in situ induction of a dense amorphous Li2 CO3 on the particle surface by a preemptive atmosphere control. Among the residual lithium compounds, Li2 CO3 is the most thermodynamically stable one, so a dense Li2 CO3 coating layer can serve as a physical protection layer to isolate the cathode from contact with moist air. Furthermore, amorphous Li2 CO3 can be transformed into a robust F-rich cathode electrolyte interphase (CEI) during cycling, which reinforces the cathode's interfacial stability and improves the electrochemical performance. The assembled coin cell with this modified cathode delivers a high discharge capacity of 232.4 mAh g-1 with a superior initial Coulombic efficiency (CE) of 95.1%, and considerable capacity retention of 90.4% after 100 cycles. Furthermore, no slurry gelation occurs during the large-scale electrode fabrication process. This work opens a valuable perspective on the evolution of amorphous Li2 CO3 in LIBs and provides guidance on protecting unstable high-capacity cathodes for energy-storage devices.

Mitigating the Kinetic Hindrance of Single-Crystalline Ni-Rich Cathode via Surface Gradient Penetration of Tantalum.

Single-crystalline Ni-rich cathodes are promising candidates for the next-generation high-energy Li-ion batteries. However, they still suffer from poor rate capability and low specific capacity due to the severe kinetic hindrance at the nondilute state during Li+ intercalation. Herein, combining experiments with density functional theory (DFT) calculations, we demonstrate that this obstacle can be tackled by regulating the oxidation state of nickel via injecting high-valence foreign Ta5+ . The as-obtained single-crystalline LiNi0.8 Co0.1 Mn0.1 O2 delivers a high specific capacity (211.2 mAh g-1 at 0.1 C), high initial Coulombic efficiency (93.8 %), excellent rate capability (157 mAh g-1 at 4 C), and good durability (90.4 % after 100 cycles under 0.5 C). This work provides a strategy to mitigate the Li+ kinetic hindrance of the appealing single-crystalline Ni-rich cathodes and will inspire peers to conduct an intensive study.